Cubic Yards to Tons Converter
Convert cubic yards to tons, or tons back to cubic yards, for gravel, sand, topsoil, mulch, asphalt millings and concrete. Pick your material and direction — the density used for the conversion is always shown, not hidden.
Quick answer: multiply cubic yards by the material's weight per cubic yard and divide by 2,000. One cubic yard of gravel or sand is about 1.35 tons, topsoil about 1 ton, mulch about a quarter ton, and poured concrete about 2 tons. Going the other way, one ton of gravel is about 0.74 cubic yards.
Example: 10 cubic yards of gravel
These are example numbers, already worked out. Change the inputs above and press the button to work out your own.
- Amount
- 10 cubic yards
- Material
- Gravel / Crushed Stone
Estimated weight
13.5 tons
- Cubic feet
- 270 cu ft
- Pounds
- 27,000 lb
- Truck loads
- 2 (at 10 tons/load)
Estimate only, worked out from the inputs shown. Confirm the order with your supplier; for slabs, posts, footings or a roof, check local building code and a licensed contractor.
Assumptions
- Gravel / Crushed Stone is assumed to weigh 2,700 lb per cubic yard (100 lb/cu ft).
- Actual density varies with moisture content, compaction and exact material grade — confirm with your supplier for large or paid orders.
- Density reference data as of 2026-09.
Planning the whole job? The gravel calculator on Build Material Planner turns your measurements into a shopping list and a cost range.
What this converter does
This tool converts a quantity of a construction material between cubic yards (volume) and tons (weight), using that material's typical density. Enter an amount in either unit, pick the material, and it works out the other unit plus cubic feet, pounds and an approximate truck-load count.
How the math works
- Cubic yards → tons: cubic yards × the material's density in lb per cubic yard, divided by 2,000.
- Tons → cubic yards: tons × 2,000, divided by the material's density in lb per cubic yard.
- Truck loads: the converted tonnage ÷ 10 (a standard dump truck's capacity in tons), rounded up to a whole load.
Why not just use a generic unit converter?
A generic length/volume converter has no idea what a cubic yard of gravel weighs — it can only convert units it already knows are equivalent, like yards to feet. Converting volume to weight requires a material's density, which is different for every material (gravel and mulch are not remotely the same weight per cubic yard). This tool bakes in typical density values for six common construction materials so you get a real weight or volume answer, not just a unit-math identity.
Weight per cubic yard chart
These are the same typical densities the converter uses, so the chart and the tool always agree. The last column is how many cubic yards fit under a 10-ton load limit.
| Material | lb per cu yd | Tons per cu yd | Cu yd per ton | lb per cu ft | Cu yd in 10 tons |
|---|---|---|---|---|---|
| Gravel / Crushed Stone | 2,700 | 1.35 | 0.74 | 100.0 | 7.41 |
| Sand | 2,700 | 1.35 | 0.74 | 100.0 | 7.41 |
| Topsoil | 2,000 | 1 | 1.00 | 74.1 | 10.00 |
| Mulch (bark / wood chip) | 500 | 0.25 | 4.00 | 18.5 | 40.00 |
| Asphalt Millings (RAP) | 2,700 | 1.35 | 0.74 | 100.0 | 7.41 |
| Concrete (poured, ready-mix) | 4,050 | 2.025 | 0.49 | 150.0 | 4.94 |
Typical published values as of 2026-09. Real loads vary with moisture, grading and how tightly the material settles. The material weights table lists where each figure comes from, with more materials, bag weights and the weight of 5 gallons of paint.
Worked examples
Yards to tons. 10 cubic yards of gravel, at a typical density of 2,700 lb per cubic yard: 10 × 2,700 = 27,000 lb, divided by 2,000 = 13.5 tons, which is about two loads for a standard 10-ton dump truck. Run this exact example →
Tons to yards. A quarry quotes 20 tons of crushed stone. 20 × 2,000 = 40,000 lb, and 40,000 ÷ 2,700 = 14.81 cubic yards. That tells you how much ground the order will cover once you know the depth you want. Run the tons example →
A light material. 12 cubic yards of bark mulch at about 500 lb per cubic yard is 6,000 lb, only 3 tons. A truck carrying mulch fills its box long before it reaches its weight limit, so mulch deliveries are priced and loaded by the yard, not the ton.
From dimensions to tons by hand
If you are starting from a patch of ground rather than a quoted quantity, work out the volume first and then convert it:
- Measure length and width in feet, and depth in inches.
- Turn the depth into feet by dividing by 12. Four inches is 0.333 ft.
- Multiply length × width × depth to get cubic feet. A 20 ft × 10 ft area at 4 inches deep is 66.67 cubic feet.
- Divide by 27, because a cubic yard is 3 ft × 3 ft × 3 ft. 66.67 ÷ 27 = 2.47 cubic yards.
- Multiply by tons per cubic yard from the chart. For gravel, 2.47 × 1.35 = 3.33 tons.
Put the cubic-yard figure into the converter above to check the weight and see the truck-load count.
Loose vs compacted material
Aggregate is sold by the loose yard or by the ton, but a driveway base or a paver bed is measured after it has been compacted. A plate compactor or roller squeezes the air out, so a yard of loose stone ends up as less than a yard in place. The weight does not change when it compacts; only the volume shrinks.
Suppliers commonly suggest ordering roughly 10% to 20% extra for material that will be compacted, with crusher run and road base toward the upper end. For the 2.47-yard example above, 15% extra is about 2.84 cubic yards, or 3.83 tons of gravel. Your supplier can tell you the figure they see with their own product, which is the number worth using.
Price per ton vs price per yard
Quarries usually price stone and sand by the ton, while landscape yards often price topsoil and mulch by the yard. To compare two quotes, put them in the same unit with the same density. For gravel at 1.35 tons per yard, a price of $30 a ton works out to $40.50 a yard, and a price of $45 a yard works out to about $33.33 a ton. These prices are only an example of the math; delivery fees, minimum loads and local rates vary widely.
Frequently asked questions
What does 1 cubic yard of gravel convert to in tons?
About 1.35 tons, using a typical gravel density of 2,700 lb per cubic yard. The exact figure varies by stone type and moisture content.
How many cubic yards are in a ton of gravel?
About 0.74 cubic yards. Divide 2,000 lb by the typical 2,700 lb per cubic yard. Ten tons of gravel is about 7.41 cubic yards.
How much does a cubic yard of topsoil weigh?
Approximately 2,000 lb (1 ton), though moisture content can push this higher, and wet topsoil weighs noticeably more than dry, screened topsoil.
How many cubic yards are in a ton of sand?
At a typical sand density of 2,700 lb per cubic yard, one ton is about 0.74 cubic yards.
How many tons is a cubic yard of concrete?
Poured ready-mix concrete weighs about 4,050 lb per cubic yard, which is 150 lb per cubic foot or a little over 2 tons per yard.
How many yards of mulch are in a ton?
About 4 cubic yards, at a typical 500 lb per cubic yard for bark or wood-chip mulch. Fresh, wet mulch can weigh more.
Why does mulch weigh so much less than gravel per cubic yard?
Mulch is a loose, low-density organic material, around 500 lb per cubic yard versus roughly 2,700 lb for gravel or sand, because it is mostly air and wood fiber, not dense mineral aggregate.
How many tons does a dump truck hold?
This converter assumes a 10-ton load for the truck count. Smaller single-axle trucks often carry less and larger tri-axle trucks more, so ask the supplier what their truck carries before you plan the number of deliveries.
Is this the same as a gravel driveway calculator?
No. A driveway calculator starts from your project dimensions and works out how much material you need. This tool starts from a known quantity, in cubic yards or tons, and converts it to the other unit for the material you pick.
Limitations
This tool estimates weight/volume using typical published density values. It doesn't account for the moisture content, compaction or exact grade of a specific supplier's material. It is not a substitute for a supplier's own weight ticket on a delivered load, and it isn't a project material calculator — it doesn't work out how much of a material you need for a given area or depth.
Put this converter on your site
Run a site for suppliers, contractors or DIYers? You can embed the Cubic Yards to Tons Converter as a free widget — responsive, no registration, and nothing added to your page beyond the calculator itself.
Cite this converter
Referencing this converter in coursework, an article or a project write-up? Grab a citation in the format you need:
Already know your project dimensions?
If you're planning a gravel driveway rather than converting a quantity you already have, BuildMaterialPlanner's gravel calculator works out cubic yards, tons and a cost range directly from your driveway's length, width and depth.